Digital Dual Channel Gauge Set with EGT Probe & Boost Sensor

  • Model: Combo-EGTS-P

Ask a Question

Starting at: $149.99

Please Choose:





Longer Cable Option (EGTS)




Pressure Sensor Option



Add to Cart:

This set includes one dual channel automobile multimeter (SYL-2813), one EGT probe with sealed tip (TC-KEGTS) and one 3 bar (48PSI) boost sensor for diesel engine (AUBER-303). The included gauge can display both the EGT reading and pressure reading at the same time. Please contact us if any questions. 
 

Red/Red Green/Green White/White

SYL-2813 gauge: 
This dual channel automobile multimeter can measure and display two parameters at the same time. It can measure temperature, pressure and other important parameters such as battery voltage and air/fuel ratio. Two programmable alarms will turn on the LED in the front panel to get the driver's attention if the temperature/pressure is above the setting point. It will also close a relay output port that can be used to turn on a buzzer, shut off the fuel, or turn on a cooling fan. Each channel contains one relay. The meter stores the peak temperature/pressure with time stamps that can be checked later. It can also operate in the peak holding mode so that only the maximum value is displayed. The brightness of the LED display can be synchronized with headlights. When the headlight is turned on at night, the display will be dimmed by the illumination signal. It can also be dimmed directly on the key pad. Developed based on industrial grade instruments, this four digits gauge offers up to 10 times the resolution and accuracy of most 3 digits gauges on the market. For thermocouple sensor, this gauge has a cold junction compensation circuit to improve the accuracy at low temperature and reduces the temperature drift when a thermocouple sensor is used. 
 
The gauge is 48 x 48 mm, slight smaller than 52mm round gauge. It is 85mm in depth. For the housing of this gauge, please check our CBox16-B

TC-KEGTS EGT probe:
The gauge is supplied with your choice of an EGT (Exhaust Gas Temperature) sensor. The model number is TC-KEGTS.  It is a K type  grounded thermocouple with a thin and sealed tip. The thin and sealed EGT probe design is widely used for aircraft applicatio­n because its durability. It is also very popular in Europe. The tip of this probe is made of Inconel 600 alloy that provides the highest working temperature available for this type of sensor. The diameter of the probe is optimized to balance the requirement of mechanical stability and the response time. The probe diameter is 3mm, with several mounting thread options available (choose from the drop down list). The insertion depth is adjustable with 1.34" (35mm) maximum.  The default cable length is 78” (2 meters). If you need a longer cable, please select the 4 meter cable option. The maximum working temperature of the sensor is 1100 ºC (2000 ºF).

TC-KEGTS Adapter Options:

1/8NPT M8x1 M10x1 Weld-in SS 1/4NPT 1/4BSPT Weld-in Carbon


AUBER-303 boost sensor: 

This pressure sensor is for diesel engine boost pressure measurements from -0.33 to 3.30 bar (or -5.0 to 48.0 PSI).  Unlike most of digital boost gauge on the market (and the other MAP sensor we offered), this sensor measures relative pressure (or gauge pressure) instead of absolute pressure. When not pressurized, the sensor will always give a zero pressure signal regardless of the elevation where the vehicle is at. It behaves the same way as the mechanical boost gauge.
 
The sensor is supplied with a matting connector and 2 meter (6ft) cable.

Gauge Specifications:

Input type Temperature Sensor, K, E, S, R, J, T, B, WRe3-WRe25, Pt100, Cu50
Pressure transducer, 0-375ohm, 0-5V, 0-75mV
Other transducer: 0-30 mV, 1-5V, 0-10V, 0-10mA, 0-20mA, 4-20mA
Display Two lines, Four digits. °F or °C, Bar, PSI, or user defined
Display resolution Thermocouple: 1°C, 1°F; RTD/CU50: 0.1°C, 0.1°F
Display brightness control 12 V illumination control signal, or key pad
Accuracy ±0.2% or ±1 unit of full input range
Control mode On-Off
Control output Relay contact: 3A at 240VAC
Alarm Relay (3A rating) high/low alarm
Recording function Maximum, Max time,
Recording time 100 hrs with 1 min, or 9999 second with 1 s resolution.
Power consumption 2 Watt
Power supply voltage rating 12 -30 VDC
Panel cutout dimension 45 x 45 mm
Dimension 48 x 48 x 85mm (1/16 DIN)


Click here for Gauge instruction manual.
Click here for EGT sensor installation guide for SYL-2813.
Click here to download Pressure Sensor Application Guide.


This product was added to our catalog on Friday 03 November, 2017.

Copyright © 2024 auberins.com.